The IHI 30NX is a mid-size compact excavator known for its reliability and performance. Proper maintenance is key to maximizing uptime and protecting your investment. Below is a clear, practical summary of the official service intervals, lubrication points, and recommended fluids.Key Highlights – IHI 30NX Maintenance
- Engine oil capacity: Max 6.3 L
- Hydraulic system: Total 56 L (Tank 35 L)
- Travel reduction gear oil: 0.5 – 0.6 L per side
- Swing gear grease: 3.7 – 4.0 L
- Daily checks include engine oil, coolant, hydraulic level, fan belt, and air cleaner indicator
- Grease all attachment pins every 50 hours
- Engine oil and filter change every 250 hours
- Hydraulic oil change every 1000 hours (or every 600 hours with breaker use)
- Use EP-2 Lithium Grease for all grease fittings
- Shorten intervals in dusty conditions or when using a hydraulic breaker
- Includes optional slide arm lubrication and adjustment
IHI 30NX Maintenance Intervals Chart
Interval | Check Point | Item | Action | Key Notes |
|---|---|---|---|---|
Daily (8 hrs) | Engine Oil | Check Oil Level | Check (E ○) | Stop engine first |
Daily (8 hrs) | Engine Coolant | Check Coolant Level | Check (W ○) | Reserve tank |
Daily (8 hrs) | Hydraulic Tank | Check Hydraulic Oil Level | Check (H ○) | Cylinders retracted |
Daily (8 hrs) | Fan Belt | Inspect / Adjust | Check tension | 10 mm deflection |
Daily (8 hrs) | Air Cleaner | Check Service Signal | Check indicator | Red = service needed |
Daily (8 hrs) | Water Sedimenter | Check Level and Drain Water | Drain if needed | Daily |
Every 50 hrs | Tracks | Check and Adjust Tension | Grease + Adjust | 10–20 mm sag |
Every 50 hrs | Fuel Tank | Drain Water and Sediment | Drain | — |
Every 50 hrs | Attachment Pins | Lubricate with Grease | Grease (G ○) | All pins |
Every 50 hrs | Swing Bearing | Lubricate with Grease | Grease (G ○) | — |
Every 50 hrs | Engine | Change Oil and Filter * | Change (E ●) | *Initial break-in only |
Every 50 hrs | Hydraulic System | Change Return Filter * | Change | *Initial break-in only |
Every 250 hrs | Engine | Change Oil and Filter | Change (E ●) | Full service |
Every 250 hrs | Air Cleaner | Service Air Cleaner Element | Clean | — |
Every 250 hrs | Fuel Filter | Drain Water and Clean Element | Clean | — |
Every 250 hrs | Coolant | Change Coolant (non-LLC) | Change (W ●) | Or every 6 months |
Every 500 hrs | Bolts | Retighten Critical Bolts | Torque to spec | Use torque table |
Every 500 hrs | Return Filter | Change Return Filter | Change (H ●) | — |
Every 500 hrs | Air Cleaner | Change Filter Element | Replace | — |
Every 500 hrs | Fuel Filter | Change Filter Element | Replace | — |
Every 500 hrs | Travel Reduction | Check Oil Level | Check (L ○) | Both sides |
Every 1000 hrs | Travel Reduction | Change Gear Case Oil | Change (L ●) | 0.5–0.6 L per side |
Every 1000 hrs | Hydraulic Tank | Change Hydraulic Oil + Clean Strainer | Change (H ●) | 56 L total. 600 hrs with breaker |
Every 2 Years | Engine Coolant | Change Coolant (with LLC) | Change (W ●) | Full flush recommended |
When Required | Battery | Inspect | Clean + Check | — |
When Required | Tracks | Check Rubber Shoes | Inspect / Replace | Replace if lugs < 5 mm |
When Required | Fuses / Fusible Link | Replace | Replace same rating | — |
When Required | Bucket | Change Bucket / Replace Tooth | As needed | Block bucket before work |
IHI 30NX Lubrication Chart
Check Point | Item | Daily | Every 50h | Every 250h | Every 500h | Every 1000h | Symbol |
|---|---|---|---|---|---|---|---|
Attachment pins | Lubricate with grease "G" | — | ○ | — | — | — | G |
Hydraulic tank | Check oil level "H" | ○ | — | — | — | ● | H |
Return filter | Change filter | — | — | — | ● | — | H |
Engine | Change engine oil "E" | ○ | — | ● | — | — | E |
Engine | Change oil filter | — | — | ● | — | — | E |
Engine | Check coolant level "W" | ○ | — | — | — | ● | W |
Swing bearing | Grease bearing | — | ○ | — | — | — | G |
Swing bearing (Ring gear) | Grease ring gear | — | — | — | ○ | — | G |
Travel reduction gear | Check / Change oil "L" | — | — | — | ○ | ● | L |
Blade | Lubricate with grease "G" | — | ○ | — | — | — | G |
Symbol Key
G = EP-2 Lithium Grease L = Gear Oil H = Hydraulic Fluid E = Engine Oil W = Coolant
○ = Check / Grease ● = Change
IHI 30NX Recommended Lubricants & Capacities
Location | Capacity | Change Interval | Recommended Lubricant |
|---|---|---|---|
Engine Oil | Max 6.3 L / Min 3.5 L | 250 hrs (initial 50 hrs) | API CD SAE 20/30/40 |
Hydraulic Oil | Total 56 L / Tank 35 L | 1000 hrs (600 hrs with breaker) | ISO-VG 46 or ISO-VG 32 |
Travel Reduction Gears | 0.5 – 0.6 L each | 1000 hrs | API CD SAE 30 |
Lower Rollers | 80 cc each | As needed | Gear Oil ISO-VG 320 (SAE 90) |
Front Idlers | 75–80 cc each | As needed | Gear Oil ISO-VG 320 (SAE 90) |
Upper Rollers | 60 cc each | As needed | Gear Oil ISO-VG 320 (SAE 90) |
Swing Gear Grease | 3.7 – 4.0 L | 1000 hrs | EP-2 Lithium Grease |
General Grease Points | As required | Every 50 hrs | EP-2 Lithium Grease |
Coolant | — | 2 years (with LLC) | Long-Life Coolant |
Quick Tips for IHI 30NX Owners
- Always complete previous service items before moving to the next interval.
- Use the hour meter as your main reference.
- Regular greasing and proper track tension are the easiest ways to extend undercarriage life.
- Breaker users should change the hydraulic oil and return filter more frequently (every 600 hours).
Comments
0 comments
Article is closed for comments.